A
-
Aboutalebi, M.R.
Quantitative analysis of thermo-mechanical behavior in 414 stainless steel using flow curves and processing maps [Volume 5, Issue 1, 2018, Pages 36-46]
-
Afshari, D.
Forming of Multi layer Sheet Metal by Drawing Process: an Analysis and FEM Simulation [Volume 5, Issue 2, 2018, Pages 36-53]
-
Alibeyki, M.
Grain Refinement of Dual Phase Steel via Tempering of Cold-Rolled Martensite [Volume 5, Issue 1, 2018, Pages 19-25]
-
Amini, S.
Simulation and Investigation of Mechanical and Geometrical Properties of St/CP-Titanium Bimetal Sheet during the Single Point Incremental Forming Process [Volume 5, Issue 1, 2018, Pages 1-18]
B
-
Bagherpour, E.
Ten years of severe plastic deformation (SPD) in Iran, part I: equal channel angular pressing (ECAP) [Volume 5, Issue 1, 2018, Pages 71-113]
-
Bagherpour, E.
Ten years of severe plastic deformation (SPD) in Iran, part II: accumulative roll bonding (ARB) [Volume 5, Issue 2, 2018, Pages 1-25]
-
Bakhshi-Jooybari, M.
A hybrid approach based on numerical, statistical and intelligent techniques for optimization of tube drawing process to produced squared section from round tube [Volume 5, Issue 2, 2018, Pages 96-109]
C
-
Chegini, M.
Quantitative analysis of thermo-mechanical behavior in 414 stainless steel using flow curves and processing maps [Volume 5, Issue 1, 2018, Pages 36-46]
E
-
Ebrahimi, G.R.
Quantitative analysis of thermo-mechanical behavior in 414 stainless steel using flow curves and processing maps [Volume 5, Issue 1, 2018, Pages 36-46]
-
Ebrahimi, R.
Ten years of severe plastic deformation (SPD) in Iran, part I: equal channel angular pressing (ECAP) [Volume 5, Issue 1, 2018, Pages 71-113]
-
Ebrahimi, R.
Ten years of severe plastic deformation (SPD) in Iran, part II: accumulative roll bonding (ARB) [Volume 5, Issue 2, 2018, Pages 1-25]
-
Esmailian, M.
Finite element simulation of two-point incremental forming of free-form parts [Volume 5, Issue 2, 2018, Pages 26-35]
F
-
Farshidi, M. H.
Optimization of die geometry for tube channel pressing [Volume 5, Issue 1, 2018, Pages 26-35]
G
-
Ghasempour Mouziraji, M.
A hybrid approach based on numerical, statistical and intelligent techniques for optimization of tube drawing process to produced squared section from round tube [Volume 5, Issue 2, 2018, Pages 96-109]
H
-
Habibian Tavan, O.
Effect of friction stir welding parameters on the ultimate tensile strength of Al-Cu tailor welded blanks [Volume 5, Issue 2, 2018, Pages 85-95]
-
Haghighat, H.
Forming of Multi layer Sheet Metal by Drawing Process: an Analysis and FEM Simulation [Volume 5, Issue 2, 2018, Pages 36-53]
-
Honarpisheh, M.
Simulation and Investigation of Mechanical and Geometrical Properties of St/CP-Titanium Bimetal Sheet during the Single Point Incremental Forming Process [Volume 5, Issue 1, 2018, Pages 1-18]
-
Hosseinzadeh, M.
A hybrid approach based on numerical, statistical and intelligent techniques for optimization of tube drawing process to produced squared section from round tube [Volume 5, Issue 2, 2018, Pages 96-109]
J
-
Joudaki, J.
Prediction of Bending Angle for Laser Forming of Tailor Machined Blanks by Neural Network [Volume 5, Issue 1, 2018, Pages 47-57]
K
-
Kadivar, M. H.
Determination of Residual Stress for Single and Double Autofrettage of Thick-walled FG Cylinders Subjected to Dynamic Loading [Volume 5, Issue 2, 2018, Pages 54-71]
-
Khalili, Kh.
Finite element simulation of two-point incremental forming of free-form parts [Volume 5, Issue 2, 2018, Pages 26-35]
L
-
Langdon, T.G.
Ten years of severe plastic deformation (SPD) in Iran, part I: equal channel angular pressing (ECAP) [Volume 5, Issue 1, 2018, Pages 71-113]
M
-
Mahzoon, M.
Determination of Residual Stress for Single and Double Autofrettage of Thick-walled FG Cylinders Subjected to Dynamic Loading [Volume 5, Issue 2, 2018, Pages 54-71]
-
Maktoubian, J.
A hybrid approach based on numerical, statistical and intelligent techniques for optimization of tube drawing process to produced squared section from round tube [Volume 5, Issue 2, 2018, Pages 96-109]
-
Mazdak, S.
Numerical and Experimental Investigation of Deep Drawing Process in Square Section of Single-Layer and Two-Layer Sheet [Volume 5, Issue 1, 2018, Pages 58-70]
-
Mirzadeh, H.
Grain Refinement of Dual Phase Steel via Tempering of Cold-Rolled Martensite [Volume 5, Issue 1, 2018, Pages 19-25]
-
Mollapour, Y.
Forming of Multi layer Sheet Metal by Drawing Process: an Analysis and FEM Simulation [Volume 5, Issue 2, 2018, Pages 36-53]
-
Moradi, S.
Numerical and Experimental Investigation of Deep Drawing Process in Square Section of Single-Layer and Two-Layer Sheet [Volume 5, Issue 1, 2018, Pages 58-70]
N
-
Najafi, M.
Grain Refinement of Dual Phase Steel via Tempering of Cold-Rolled Martensite [Volume 5, Issue 1, 2018, Pages 19-25]
P
-
Pardis, N.
Ten years of severe plastic deformation (SPD) in Iran, part I: equal channel angular pressing (ECAP) [Volume 5, Issue 1, 2018, Pages 71-113]
-
Pardis, N.
Ten years of severe plastic deformation (SPD) in Iran, part II: accumulative roll bonding (ARB) [Volume 5, Issue 2, 2018, Pages 1-25]
R
-
Razi Mousavi, S. H.
Determination of Residual Stress for Single and Double Autofrettage of Thick-walled FG Cylinders Subjected to Dynamic Loading [Volume 5, Issue 2, 2018, Pages 54-71]
-
Reihanian, M.
Ten years of severe plastic deformation (SPD) in Iran, part I: equal channel angular pressing (ECAP) [Volume 5, Issue 1, 2018, Pages 71-113]
-
Reihanian, M.
Ten years of severe plastic deformation (SPD) in Iran, part II: accumulative roll bonding (ARB) [Volume 5, Issue 2, 2018, Pages 1-25]
S
-
Safari, M.
Prediction of Bending Angle for Laser Forming of Tailor Machined Blanks by Neural Network [Volume 5, Issue 1, 2018, Pages 47-57]
-
Safdarian, R.
Effect of friction stir welding parameters on the ultimate tensile strength of Al-Cu tailor welded blanks [Volume 5, Issue 2, 2018, Pages 85-95]
-
Safikhani, H.
Multi-objective Pareto optimization of bone drilling process using NSGA II algorithm [Volume 5, Issue 2, 2018, Pages 72-83]
-
Sakhtemanian, M.R.
Simulation and Investigation of Mechanical and Geometrical Properties of St/CP-Titanium Bimetal Sheet during the Single Point Incremental Forming Process [Volume 5, Issue 1, 2018, Pages 1-18]
-
Setoudeh, F.
Multi-objective Pareto optimization of bone drilling process using NSGA II algorithm [Volume 5, Issue 2, 2018, Pages 72-83]
-
Seyedein, S.H.
Quantitative analysis of thermo-mechanical behavior in 414 stainless steel using flow curves and processing maps [Volume 5, Issue 1, 2018, Pages 36-46]
-
Sharifi, E.
Numerical and Experimental Investigation of Deep Drawing Process in Square Section of Single-Layer and Two-Layer Sheet [Volume 5, Issue 1, 2018, Pages 58-70]
-
Sheykholeslami, M.R.
Numerical and Experimental Investigation of Deep Drawing Process in Square Section of Single-Layer and Two-Layer Sheet [Volume 5, Issue 1, 2018, Pages 58-70]
T
-
Tahmasbi, V.
Multi-objective Pareto optimization of bone drilling process using NSGA II algorithm [Volume 5, Issue 2, 2018, Pages 72-83]
-
Tsuji, Nobuhiro
Ten years of severe plastic deformation (SPD) in Iran, part II: accumulative roll bonding (ARB) [Volume 5, Issue 2, 2018, Pages 1-25]
Your query does not match with any item